If you are encountering login problems please check here
Search Results
Hi I have 87 turbo coupe. It's been sitting in storage for years. I need some parts to get it running again but I want to set it to race it.  Looking for a bigger exhaust  downpipe for the car, Thinki...
504
Well I'd say compressor housing is set up for a 50 trim wheel, backing pad opening is almost exactly 3" and the smallest part of the machined funnel inside the intake housing is a apx. 2.25" but not s...
455
Oh I just seen where you said a 50 trim compressor wheel, my T4 intake housing is a A/R .50 so maybe that's why you need a 50 trim wheel.
455
So by stage 3 turbine are you just talking about the wheel for the exhaust side? or is it a special extra large exhaust housing for the turbo also? Or are you saying they use a stage 2 or stage 3 whee...
455
Hi I'm getting back to working on my 87 turbocoupe after years of it being in storage. I have quite a lot of parts I've bought while it was sitting but am not sure all of them are right for the car. F...
455
Hi buying a 2.3 turbo block does sound better, easier and simpler.It would deal with stuff like oil return from turbo to block better,also turbo motor might have better oiling system too. It's just th...
712
Hi I'm trying to convert my 85 ranger 2.3 motor into a 2.3 turbo motor. I thought I had good used stock 2.3 turbo pistons to use,But they wern't any good. Anyone know a good quality piston to use? Thi...
712
So as I understand it there is no way to use air conditioning at all because there is only room if you use a non air conditioned heater box.even then you have cut corner of box for O2 sensor room and ...
1,400
Thanks for the replies,sorry it took me so long to get back here. I sent a email on the adapters to flip the exhaust manifold.Don't know if that will work for me though. What do you do for oil and wat...
1,400
Yes it does. For that reason I toyed with the idea of using a 1980 carb type turbo system. I Have that complete system and a holley 2 barrel carb and hooker header I could have used to modify it with....
1,400
Hi I'm getting ready to do a turbo swap into a 88 ranger pickup. I heard that the exhaust housing will hit the heater box using the standard e6 exhaust manifold. Will this be much of a problem if you ...
1,400
Thanks for the replies. the motor had one of the rods go through the oil pan. Haven't had a chance to open it up yet to check it out. It's been sitting in my garage for about 15 years. I thought it ...
618
Hi I got a old 1980 carb version of the 2.3 turbo motor I'm junking and am not sure what parts I should keep off of it. I understand that year had forged pistons stock so I'm for sure saving them but ...
618
Thanks I knew someone would know. I'm going to look at this air bag setup saturday.I didn't want to buy something that didn't fit. This is a easy/street air bag system I wish it was the shockwave sys...
357
Hi I need to know the differences between the two. I've found a air bag setup for the Mustang II,I want to put it on my 74 Pinto. The interchange book shows bottom control arms are different and I'm t...
357
Hi I'm building a turbocoupe. Talked to a local 2.3 car owner at a car show,his car was built. I'm tring to do some of what he had done.He mounted a supercoupe throttle body on a gutted rotated stock ...
414
How do you use the plate on your XRTi and whare is it found on the Volvo? Is it used as a oil cooler? Oh that second intercooler turned out to be off a Audi not a volvo. The junk yard is having a 50% ...
211
Hi I looked for a Volvo intercooler at a junkyard. I found two different types. one was very thin but large in size and had in and outlets at top facing motor. I think this one is the one most people ...
211
The crack in the .63 housing isn't that bad but I was worried it might spread wider as it got hot. Thought about welding it up but it's cast iron,[kinda tricky welding] and you probley have to mill it...
367