If you are encountering login problems please check here
Search Results
.  WELCOME to TurboFord, DD.......what's your name? When you say that "a 5spd Ranger just fell into my lap".....does that mean you now own it? If so, I doubt that you'll find enough improvement in pow...
48
. Hey, Andy ~ You're posting to a thread that's 20 years old! 
1,230
. Be sure to check the guide(s) for wear, Landy. If any are worn/loose, you'll need to remove the head for replacement or for inserts, sooooo.......you might be better off pulling the head as you wer...
90
. Agreed, BUT......I think you'd get better results with a "Wanted" ad. Also, Renai "Chip" Givens would have a set. My 2¢...... 
261
. You DO realize that Mike's FS post is nearly 4 years old, right? 
261
. The OEM PCV valve wasn't factory-installed in the hose from the v/cover, Andy.......rather, it was located in an S-shaped hose that attached to the crankcase canister we've been discussing, then a s...
184
. Any of the following 5 part numbers will get you an iteration of the elusive/NLA/unobtanium 2.3 Lima "crankcase-vent canister" (baffle, air/water separator, etc.), similar to the one depicted below....
52
. Ford installed those crankcase air/water separators (vent baffles) with a hardening sealant, so - if you plan on harvesting one - I suggest (1) Trying to twist/rotate it first to break the sealant l...
184
. HERE (https://www.tascaparts.com/oem-parts/ford-oil-cooler-f4tz6a642a?origin=pla&gclid=Cj0KCQjwmcWDBhCOARIsALgJ2QfoGRL-onhaPI5py-SBJxzkUO0Oc16EZ1VPWTCZlGZbF8tL7A54_CcaApU2EALw_wcB) (
184
. DITTO.....besides, you ain't gonna fit those springs in yer head without cutting the pockets, since their ID and OD are smaller/bigger respectively ~ you're gonna have to make another trip to yer ma...
205
ianb Wrote: (04-09-2021, 10:44 AM) -- ......where there should be a SpOut (shunt) is a disconnect from the tfi plug going to somewhere in the harness under the hood.   -- . I ASSume that the wannabe...
204
. WELCOME, Slumlord.......what's your name? California boy here (born and raised) = so, not many rusted cars 'round hyar except those left outdoors since the early/mid 20th century OR from outta stat...
266
. With all due respect to Dave ......it's a lot easier, at least for me, to simply use a 1/4-drive 5/16 or 8mm socket and extension. You can certainly use a speed handle, as suggested, but I just ch...
153
firewheel56 Wrote: (04-08-2021, 02:46 AM) -- .....after putting in a new plug on #3 cylinder it will run good 15 lbs boost for about 5 miles and the plug is fouled.   -- . What kinda "fouling", Land...
3,772
teal95 Wrote: (04-06-2021, 01:31 PM) -- When I went to disconnect the shifter, I found......I have to pull the console to get at all the bolts.  -- . It's been a while, BUT.....aren't there two bolt...
918
. LOL.....I figured I could shake SOMEONE  outta the trees with that comment!   :D
3,772
. 👍  BTW.......I'm sure you must realize by now that we've been the only ones on TF for the past 4 days (except for the spammers). 
3,772